Brian Staruk

Bastille Smoky Vanilla & Bourbon Street Loaf Soap

noteupdated

  • Mold: Nurture Handmade 5 lb Premium Soap Mold (18” L x 3.5” W x 2.5” H liner cavity)
  • Yield: ~13 bars at 3cm per cut | Cure time: 4–6 weeks | Active time: ~1 hour
  • Scaled from: Standard Bastille recipe at 1,600g oils — the safe ceiling for this mold

Safety First

  • Always wear safety glasses and gloves before handling lye
  • Lye (sodium hydroxide) is caustic — it will burn skin and eyes on contact
  • Always add lye to water, never water to lye
  • Work in a well-ventilated area
  • Designate all soap equipment as soap-only — never return to kitchen use

Recipe

Component Amount Notes
Olive oil 1,152g Any grade — 72% of oils
Coconut oil, refined 76° 288g Refined, not virgin — 18% of oils
Castor oil 160g Boosts lather — 10% of oils
Distilled water 608g Must be distilled, not tap (38% of oil weight)
Sodium hydroxide (lye) 218g Confirmed in SoapCalc — 5% superfat, this oil blend. See note below.
Sodium lactate 20ml (4 tsp) 1 tsp per lb of oils; add to cooled lye solution
Smoky Vanilla Woods FO 52g Nurture Handmade; 50% of FO blend
Bourbon Street FO 52g Nurture Handmade; 50% of FO blend
Kaolin clay ~32g Pre-mix into a splash of combined oil before adding to batter

5% superfat. Oil blend is 72% olive / 18% coconut / 10% castor. Fragrance is at the strong rate (~6.5% of oil weight, 104g total) in a 50/50 Smoky Vanilla Woods : Bourbon Street blend.

Lye confirmed in SoapCalc. At 1,600g oils (72/18/10 olive/coconut/castor) and 5% superfat, SoapCalc returned 217.90g NaOH — rounded to 218g here. Lye concentration 26.38%, water:lye ratio 2.79:1. Weigh to the gram.


Instructions

Step 1 — Gear Up

Put on safety glasses and gloves. Set up the basement workspace with good ventilation. Pre-weigh all ingredients into separate containers before starting.


Step 2 — Prep the Mold

Assemble the Nurture 5 lb wood mold with the silicone liner seated flat inside. Confirm the liner is fully pushed into the corners. Clear acrylic lid ready but off to the side.


Step 3 — Make the Lye Solution

(Allow ~30 minutes to cool)

  1. Make sure the 2qt stainless bowl is bone dry
  2. Weigh 218g lye into one of the 1-cup stainless prep bowls and set aside
  3. Weigh 608g distilled water into the 2qt bowl
  4. Slowly pour the lye into the water — never reverse this
  5. Stir until fully dissolved — solution will heat sharply and release brief fumes; don’t lean over it
  6. Add 20ml (4 tsp) sodium lactate and stir in
  7. Set aside to cool to approximately 105–120°F

Step 4 — Prepare the Oils

  1. Melt 288g coconut oil until liquid
  2. Combine with 1,152g olive oil and 160g castor oil in the 6qt stockpot; heat on the induction element to ~110°F
  3. Stir the 32g kaolin clay into a small splash of the combined oil until a smooth slurry forms; set aside
  4. In a small cup, combine 52g Smoky Vanilla Woods and 52g Bourbon Street; set aside
  5. Confirm oils are within ~10°F of the lye solution before combining

Step 5 — Combine and Reach Trace

  1. Pour the cooled lye solution into the stockpot of oils
  2. Stick blend in 5–10 second bursts, alternating with hand stirring
  3. Aim for light trace — batter thickens to a thin pudding and drizzled batter leaves a trail
  4. Expect 3–8 minutes of blending with this oil blend

Step 6 — Add Clay and Fragrance

  1. Stir the kaolin slurry into the batter
  2. Pour in the pre-combined FO blend and hand stir 1–2 minutes — do not stick blend after adding FOs
  3. Neither fragrance accelerates, so you have working time — but don’t dawdle

Step 7 — Pour and Insulate

(Rest 3–4 days in mold)

  1. Pour batter into the lined mold; tap gently to release air bubbles
  2. Smooth the top with a spatula
  3. Spritz the surface with 99% IPA to prevent soda ash
  4. Set the clear acrylic lid on — no towel needed
  5. Leave undisturbed; extended in-mold time of 3–4 days is fine and does not harm the soap

Step 8 — Unmold and Cut

  1. Remove the wood sides, then push the loaf out via the bottom holes
  2. Peel the silicone liner away
  3. Cut into bars at 3cm using the Nurture wire cutter — yields ~13 bars
  4. If bars crumble they needed more time; firm and fine-grained is correct

Step 9 — Cure

(4–6 weeks minimum)

  1. Arrange bars on a rack with airflow on all sides
  2. Store in a cool, dry place out of direct sunlight
  3. Cure a minimum of 4 weeks; 6–8 weeks is better for high-olive bars
  4. Label bars with the batch date

Batch Notes

  • Manly “guy” bar — 50/50 Smoky Vanilla Woods + Bourbon Street
  • Expect a deep brown bar: vanillin in SVW plus tonka bean in Bourbon Street both brown heavily. Embrace it for the kraft-wrap aesthetic.
  • First batch at the full 1,600g oil ceiling for the Nurture mold — Batch #3 overflowed at 1,787g; this stays under
  • Fragrance at strong rate (104g total) per standard preference
  • Lye confirmed in SoapCalc before mixing: 218g (217.90g exact; 26.38% lye concentration, 5% superfat)

Resources

back to contents